Low Heat Release Crystal Clear Epoxy Resin Coffee Table Casting Moisture Proof

Low Heat Release Yellow Resistance Crystal Clear Epoxy Resin For Contemporary Coffee Table Casting

Product description

Epoxy Resin 400-4AB is a TOP coat Food grade epoxy resin that cures under normal and low temperature conditions. It has good leveling, natural defoaming, low viscosity, high hardness and high strength. It can be cured at room temperature or by heating. Dedicated to crystal drop board, marble board, 3D floor insulation, metal floor, kitchen countertop, resin coating, high hardness coating on any surface; and other electronic parts, moisture-proof potting, secret masking, etc.

Features
High water clear appearance
High hardness
High gloss
Easy application
Easy to clean

Advantages
High water clear appearance
High hardness
High gloss
Easy application
Easy to clean

Conditions of Use

1) Ratio: A:B=100:33(weight ratio)

A: B=100:50(Volume ratio)

2) Hardening conditions: 25℃×8H-10H OR 50℃×1.5H(2g)

3) Pot life: 25℃×20min(100g)

TIP:

MC400-4AB and MC00-5AB different Pot life

At 30 degrees Celsius:

MC400-5AB: 10-20 kg, used up in 15 minutes

MC400-4AB: 8-10 kg, used up in 15 minutes

At 20-25 degrees Celsius:

MC400-5AB: 10-20 kg, used up in 15 minutes

MC400-4AB: 10-15 kg, used up in 15 minutes

At 10-15 degrees Celsius:

MC400-5AB: 20-30 kg, used up within 20 minutes

MC400-4AB: 15-20 kg, used up within 20 minutes

Use method

1. Working environment: Please keep the plastic container clean. A, B components are strictly according to the weight ratio, accurately weighed, and stir it evenly along the inner wall of the container clockwise until it is used for 3-5 minutes.

2. According to the operating time and amount of glue deployment, to avoid waste. When the temperature is lower than 15 °C, please pre-heat the A glue to 30 °C and then adjust the rubber, easy to operate (low temperature, A glue will thicken ); After use must seal the lid, to avoid the product due to moisture absorption scrapped.

3. When the relative humidity is more than 85%, the surface of the cured product can easily absorb the moisture in the air to form a white mist. Therefore, when the relative humidity is more than 85%, it is not suitable for room temperature curing. It is recommended to use the heating and curing.

4. The lid must be sealed after use to avoid the product being scrapped due to moisture absorption.

Hardened property

1) Hardness: shore D <90

2) Withstand voltage: KV/mm 22

3) Bending strength: Kg/mm2 23

4) Volume resistance: Ohm3 1x10*15

5) Surface resistance: Ohmm2 5X10*15

6) Thermal conductivity: W/M.K 0.61

7) Lure power loss: 1KHZ 0.42

8) Heat distortion temperature: ℃ 80

9) Water absorption: % <0.15

10) Compressive strength: Kg/mm2 13.4

The above performance data is typical data measured in a laboratory environment with a temperature of 25°C and a humidity of 70%. It is for customer reference only.

Lab Equipment

Caution
1, The operating environment should be ventilative and should keep away from fire. Closely sealed after use.
2, Avoid eye contact, in case of contact, wash with plenty of water and get medical attention immediately.
3, If contact skin, wrap with clean cloth or paper, and wash it with water and soap.
4, Keep away from children.
5, Please take a trial before application to avoid usage mistake.

Storage And Shelf Life
1, Store at the temperature of 25°C or cool and dry place. Avoid from sunlight, high temperature or high humidity environment.
2, Use up as soon as possible when opened. It is strictly forbidden to expose to the air for a long time after it is opened to avoid affecting the quality of the products. The shelf life is six months in the room temperature of 25°C.